Mining and Geotechnical Applications
A hands-on technical course on Mining and Geotechnical Applications at RIC2027
Begin your RIC2027 experience with a full day of hands-on learning. On April 18, 2027, the first day of the conference, we’ll host this full-day technical course, designed to complement the main conference program.
This full-day course follows an open-pit case study from site data and material strength to bench design, slope stability, and waste dump runout. You’ll explore how geological structures influence bench performance, how strength assumptions shape a model, and what a potential dump failure could mean for nearby infrastructure.
The course then moves underground, using a cavern example to examine how rock responds to excavation and how that response changes with excavation sequence and three-dimensional geometry.
Each module centres on an engineering question, combining hands-on exercises, prepared models, and demonstrations. Along the way, you’ll connect familiar workflows with new tools and gain an introduction to programs you may not have used before.
What You’ll Learn
By the end of the course, you’ll have explored how to:
- Turn geological sections and rock strength data into inputs for an open-pit model.
- Fit a rock-mass strength envelope and understand the modelling decisions behind it.
- Evaluate structurally controlled bench failures and investigate bench face angle and berm width.
- Compare bench-scale results with the changing structural conditions around a 3D pit wall.
- Connect a potential waste dump failure volume to a runout scenario and interpret its consequences.
- Assess cavern displacement, yielding, and stress redistribution through excavation stages.
Recognize where a 2D section represents underground behaviour well and where 3D geometry needs closer attention.
Course Modules
Module 1: One Open Pit, Three Design Questions
Course orientation and case study introduction
What do you need to understand about the pit before you begin analysing it?
Meet the open pit that connects the day’s modules: a small number of geological units, a weak plane within a foliated or bedded unit, mapped joint sets on one wall, a critical section, and a waste dump beside the pit.
Use this setting to frame three questions:
- Will the benches stand? Explore structurally controlled failure with RocSlope2 and RocSlope3.
- Will the overall slope stand? Consider rock-mass and weak-plane failure through Slide2 and RS2, with Slide3 providing 3D context.
- If the waste dump fails, where will the material go? Introduce the connection between stability analysis and runout assessment.
A short orientation to shared Rocscience interface conventions will help you navigate the programs used throughout the day.
Module 2: From Site Data to an Open-Pit Model
RSData, RSInsight, and Slide2, with inputs from RSLog and RSGeo
What does the slope look like, and how strong is it?
Build the foundation for the pit analysis by bringing geological information and rock-mass strength parameters into Slide2. Focus on the choices that shape the model—and the engineer’s responsibility to review and complete it.
- Import a profile from RSLog and a pit section from RSGeo. These programs provide the inputs but are not taught in this course.
- Fit a Generalized Hoek–Brown strength envelope in RSData, moving from intact-rock properties to rock-mass parameters using Geological Strength Index (GSI) and disturbance.
- Transfer the material parameters to Slide2.
- Use RSInsight to start the model from the imported section, then complete the pit geometry, water table, and search limits manually.
The emphasis is on understanding the strength envelope as a consequential modelling choice and treating assisted model creation as a starting point—not a substitute for engineering judgement.
Module 3: Bench Design and Structurally Controlled Failure
RocSlope2 and RocSlope3
What bench face angle and berm width can this wall accommodate?
Investigate how joints influence bench stability and how bench configuration contributes to inter-ramp and overall slope geometry.
- Load the wall’s joint sets from a prepared Dips file into RocSlope2 and set the slope orientation.
- Run planar, wedge, and toppling analyses, then identify the joint combinations that form blocks and review their factors of safety.
- Use Bench Design to explore probability of failure against bench face angle for a fixed inter-ramp angle, and examine the berm width needed to catch failures.
- Apply the same joint sets to the 3D pit wall in RocSlope3.
- Review where removable blocks concentrate as wall orientation changes, using heat maps to examine the lowest factors of safety and largest block volumes.
Compare a bench assessment at a defined orientation with the variation revealed around a three-dimensional pit wall.
Module 4: Waste Dump Stability and Runout
Slide3 and RSRunout
If the dump fails, what happens next?
Connect stability results to a runout scenario to examine both the potential release and what lies in its path.
- Open a prepared dump-on-foundation model in Slide3 and review its static factor of safety.
- Identify the potential failure surface and release volume.
- Use that release volume in a single RSRunout scenario.
- Review runout distance, velocity, deposit extent, and whether the material reaches a haul road, ramp, infrastructure, or watercourse.
- Discuss which findings could inform changes to setback, lift height, toe buttressing, or foundation preparation—and which provide context rather than directly determine the design.
Module 5: From Surface Excavation to an Underground Cavern
RS2 and RS3
How does the ground respond when excavation takes place inside the rock rather than at the surface?
Shift from slope stability to the displacement, yielding, and stress changes around an underground opening. Rather than looking for one summary result, examine what happens at specific locations and excavation stages.
In the hands-on RS2 exercise, you’ll:
- Open a prepared, meshed cavern model with materials assigned from the RSData strength envelope.
- Set the in-situ stress field and define three stages: in-situ conditions, top-heading excavation, and the full opening.
- Use query points to review total displacement at the crown and the midpoint of each sidewall.
- Examine yielded elements, the depth of yielding around the opening, and major principal stress concentrations and reductions.
- Compare the top-heading and full-opening stages to see how displacement develops as excavation progresses.
A pre-computed RS3 demonstration introduces the same cavern with an access tunnel meeting one end. Review displacement contours along the cavern axis and compare the mid-length response with the 2D section to understand where the plane-strain assumption is representative.
Apr 18, 2027 - Apr 18, 2027
Rio de Janeiro, Brazil
The course will be conducted in English, Portuguese