The Rocscience International Conference 2021 Proceedings are now available. Read Now
 

Search Results

Advanced

The Advanced page in the Project Settings dialog includes the following options for customizing parameters of the limit equilibrium analysis.

Project Settings Dialog - Advanced Tab

  • Maximum allowed columns with base tension (%)

During the computation process, the program determines the base effective normal stress. After computation of a factor of safety, this check determines the percentage of columns which have tension (negative base effective normal stress), if this percentage is greater than the percentage defined in the dialog, the program generates a -411 error code for this surface and the factor of safety is discarded. Since the factor of safety is for sliding, this check can be used to determine when too much tension violates the sliding mode of failure assumption.

  • Zero Shear Strength when base in tension

When a column base has negative effective normal stress, it’s deemed in tension. How a limit-equilibrium program such as Slide2 and Slide3 determines shear strength along the base of such a column can vary. By default, the program assumes that the negative effective normal stress can not exceed the tensile strength of the material. The tensile strength is defined in the material properties dialog and is zero by default for most materials except materials with the failure criterion set as Generalized Hoek-Brown. If the effective normal stress exceeds the tensile strength, and this option Is on, the shear strength is set to zero and the normal stress is set to the value which gives equilibrium for the column. If this option is off (default), the effective normal stress is set to the tensile strength and the shear force on the base is set to a value which produces equilibrium on the base. The assumption here being that the tensile mode of failure does not warrant the shear factor of safety for determining the shear force on the base. Thus, all columns that are in tension have their own tensile factor of safety when computing the ratio of shear strength to shear stress. The benefit of this method is that it negates fictitious tensile forces, like the method in Slide2 for automatically removing tension or the manual addition of a tension crack.

  • Maximum base angle

To compute factor of safety, a slip surface is approximated with a set of columns. It is a known problem that very steep base angles of discretized columns can impose numerical difficulty on limit equilibrium methods and may lead to unreliable computation of factor of safety.

Maximum base angle option which is set enabled by default, limits base dip angle to maximum 80 degrees, it means the engine would discard any slip surface that has columns with base angles that do not satisfy this condition. Users may change default value of 80 degree or even disable this constraint.

  • Initial Failure Direction Trend:

As part of the solution process, the program determines the direction of failure that yields the same factor of safety for all equilibrium equations in force and/or moment. The initial direction of failure is determined automatically based on the resultant direction of the overall driving force neglecting interslice forces. The program then iterates to find the true direction of failure. If the user wishes to define their own initial failure direction, they can use this option. This is a useful option when the failure direction is known for a particular user-defined surface.

  • Force Failure Direction Trend:

This option currently does the same thing as the Initial Failure Direction Trend. In the future, a user will be able to define the failure direction trend and the program will try and determine the FS in this direction.

  • Translate model to origin if needed for precision:

Sometimes the location of a model geometry are very large numbers. If dimension of the model geometry is relatively much smaller compared to these coordinates, numerical computations can suffer from precision loss. To minimize this effect, when this option is enabled and before starting the computations, the model is translated to the origin of the coordinate system. After finishing the computations, the model is translated back. This option is set enabled by default and is advised to remain enabled.

  • Ignore slip surface discretization errors:

There are a series of error codes associated with the shape or discretization of slip surfaces. To get a valid factor of safety, by default these error codes are enabled. However, by enabling this option, users can disable such error codes. Here is a short description of these error codes:

-113: slip surface too close to search boundaries

Slip Surface Search Boundaries Model

-114: slip surface has reverse curvature

Slip Surface Reverse Curvature Model

-115: slip surface does not meet minimum depth defined in surface filters

-121: slip surface is not convex

-136: minimum elevation of the slip surface is in violation of defined value in surface filters

-141: slip surface falls below external geometry

Iteration Parameters

This section deals with some parameters used in solving LEM equations for Spencer and GLE methods. Changing these parameters can impact the convergence behavior of the solver for finding factor of safety.

  • Minimum lambda (Spencer, GLE)
  • Maximum lambda (Spencer, GLE)

Lambda is related to the ratio of interslice shear to normal force for the GLE and Spencer’s method. For Spencer’s method, lambda is equal to the tangent of the inclination of the interslice resultant force. It is well known that multiple roots to the factor of safety equations can exist with invalid roots noticeable by kinematic infeasible interslice and/or base forces. The limitations on lambda are to prevent convergence to these kinematically invalid roots. Negative values mean reverse shear and are generally not advisable, thus the -6 degree (lambda=-0.1) minimum default limitation. Interslice force resultants greater than 80 degrees (lambda=6) are also not advisable, thus the maximum default. These limitations are taken from UTEXAS4 and discussions on the topic with Steve Wright.

  • Initial trial value of FS

The initial guess used during the iteration process for the computation of factor of safety.

  • Minimum iteration FS

The minimum possible value of factor of safety during iteration, the program generates a -200 error code if this check is used. This option is off by default

  • Maximum iteration change in FS

During iteration of the factor of safety, the absolute difference in factor of safety values used in successive iterations cannot exceed this value. This option is off by default.

Account Icon - click here to log in or out of your account Shopping Cart icon Click here to search our site Click here to close Learning Tech Support Documentation Info Chevron Delete Back to Top View More" PDF File Calendar Location Language Fees Video Click here to visit Rocscience's LinkedIn page Click here to visit Rocscience's YouTube page Click here to visit Rocscience's Twitter page Click here to visit Rocscience's Facebook page Click here to visit Rocscience's Instagram page Bookmark Network Scroll down for more Checkmark Download Print Back to top Single User Multiple Users CPillar Dips EX3 RocFall RocPlane RocSupport RocTopple RS2 RS3 RSData RSPile Settle3 Slide2 Slide3 SWedge UnWedge Commercial License Education License Trial License Shop safe & secure Money-back guarantee