Expert Modelling: Hands-on help from Rocscience Engineers. Register Here
 

Search Results

Probabilistic analysis with random shear strength (COV)

1.0 Introduction

This tutorial introduces the ability to define variability on the shear strength of a material itself. It has two important advantages:

  1. It eliminates the need to define variability on multiple individual parameters for a material, particularly helpful in cases where parameter-specific data may be sparse.
  2. It can be applied to all material strength types, including Shear/Normal Function, all Anisotropic options, and Discrete Function.

Finished Product:

The finished product of this tutorial can be found in the Tutorial 39 COV.slmd data file. All tutorial files installed with Slide2 can be accessed by selecting File > Recent Folders > Tutorials Folder from the Slide2 main menu.

2.0 Project Settings

After opening Slide2, select File > Recent > Tutorials folder from the Slide2 main menu and open Tutorial 39 COV – starting file.

You should see the following open pit section:

Project Settings spencer method

You can click on Analysis > Project Settings to see that the Spencer method is selected. You can also click on Surfaces > Surface Options to see that Particle Swarm non-circular search is selected.

3.0 The Model

Select: Properties > Define Materials.

You will notice that the yellow material is a Shale with a Shear/Normal Function strength type. You can click “Edit” to see the Shear/Normal function.

The green material uses the Generalized Anisotropic Strength Type. You can click Edit to see that the function is defined by two other materials:

Generalized Anisotropic Strength Type

Click Cancel and select the Anisotropic Linear material. You will see this follows an anisotropic surface. Click Cancel.

Click Analysis > Compute to run the analysis. Once done, select Analysis > Interpret to view the results. You will notice a minimum surface that intersects all three materials, with a Factor of Safety of about 1.2. Close Interpret and return to the Modeler.

3.1 COV OPTION

Right click on the “Group 1” group in the Document Viewer and click “Add Scenario.” Then right-click on the scenarios and click “Rename.” In the dialog name the new scenario “COV.”

To use the COV option, we first have to enable Probabilistic Analysis. To do this:

  1. Select Analysis > Project Settings.
  2. Click on the Statistics tab.
  3. Check the “Probabilistic Analysis” box.
  4. Then set the number of samples to 50 and the Analysis Type to Overall Slope as shown.
  5. Click OK.

project settings statistics Probabilistic analysis

Now the Statistics tab will appear in the menu bar.

Select: Statistics > Materials.

You will notice the “Define shear strength using COV” button. Check this to enable the option for the Shale material. You will see two input fields appear as shown:

Material Statistics define shear strength

This means that the shear strength of the Shale will vary according to a lognormal distribution, with a coefficient of variation of 0.2 The coefficient of variation is defined as standard deviation divided by the mean. Because the shear strength value changes according to location, the user only needs to define the standard deviation as a fraction of the mean.

If the user would like to reference a typical range for a material, they can select the COV table button outlined in the image above. We see that COV values typically do not exceed 0.5. We see that for clay and silt the COV is typically less than 0.1, so we will input a value of 0.1 in the COV box.

Now click on Generalized Anisotropic in the sidebar and check the COV box. Select a Uniform Distribution. You will notice that the COV box is replaced by a range. This is because certain distributions (uniform, triangular, exponential) do not take a standard deviation (and hence a COV) input. Change the range to 0.75 and 1.25:

Generalized Anisotropic COV

The meaning of this is that in each simulation the shear strength value calculated at a given location will be multiplied by a value between 0.75 and 1.25. Hence, we are saying that the shear value determined by the material input parameters may not be exactly that, and we want to consider some plus/minus variability in the shear strength.

Now select the Anisotropic Linear material. This time click the Add button. You will notice that all the individual parameters for this strength type can be defined as separate random variables.

add random variables

Alternatively, we can define the shear strength itself as a random variable. Select cancel, and define a COV random variables with Lognormal Distribution and a COV of 0.2.

Notice that you can also define random shear for Soil Mass and Bedding materials, which make up the Generalized Anisotropic material. Keep in mind that if you do so, these random variables will be independent of the random shear in Generalized Anisotropic, meaning they will not be derived from the Generalized Anisotropic material’s random shear. However, if you would like them to be dependent, you can always define correlation using the Correlation button as you see fit.

We will stick with these three random variables. Click OK. Now click Analysis > Compute and then OK in the dialog to proceed.

Because this is an Overall Slope analysis, a new limit equilibrium analysis is done in each of the 50 simulations and a new surface may be found in each. The computation may take a few minutes. Once done, open up Interpret.

We see that the Probability of Failure is 14%. Turn off the material colours from Display Options in the left sidebar to better see the minimum surfaces that were determined in each simulation.

Display Options material colours

Notice that all surfaces adhere to the anisotropic surface. It is important to note that the random shear option means that the shear strength at each x,y point in the slope follows the distribution defined by the user throughout the 50 simulations. It does not mean that the anisotropic angle is random. For example if you were to take the shear strength value at point (-50, 500) above, and make a histogram of the shear strength at that point from the 50 simulations, you would see the distribution shape defined for the Generalized Anisotropic material.

Select Statistics > Histogram Plot and plot the Shale Shear Strength Factor. You will see the lognormal distribution originally defined:

histogram Shale Shear Strength Factor

The mean is 1.0: shear strength is multiplied by 1.0 in the deterministic case. Right click on the plot and select “Change plot data.” Switch to Generalized Anisotropic Shear Strength Factor and you will see the uniform distribution we defined. Now switch to factor of safety and click Done.

Histogram Generalized Anisotropic Shear Strength Factor

These are the 50 factor of safety values computed: they range between approximately 0.7 and 1.6.

4.0 Additional Exercise 1

For the sake of the tutorial we have computed a small number of simulations and see a small number of surfaces in varying locations based on the varying shear strength. As an additional exercise, the user can try running 1000 simulations to see the resulting failure modes and results.

additional exercise result modes

5.0 Additional Exercise 2

The COV option is also available for spatial-enabled strength types. Try out Tutorials 33 and 34 with random shear strength and compare to random cohesion and friction angle:

Additional Exercise 2 COV

This concludes the COV tutorial.

Account Icon - click here to log in or out of your account Shopping Cart icon Click here to search our site Click here to close Learning Tech Support Documentation Info Chevron Delete Back to Top View More" PDF File Calendar Location Language Fees Video Click here to visit Rocscience's LinkedIn page Click here to visit Rocscience's YouTube page Click here to visit Rocscience's Twitter page Click here to visit Rocscience's Facebook page Click here to visit Rocscience's Instagram page Bookmark Network Scroll down for more Checkmark Download Print Back to top Single User Multiple Users CPillar Dips EX3 RocFall RocPlane RocSupport RocTopple RS2 RS3 RSData RSPile Settle3 Slide2 Slide3 SWedge UnWedge Commercial License Education License Trial License Shop safe & secure Money-back guarantee