The Rocscience International Conference 2021 Proceedings are now available. Read Now
 

Search Results

Borehole Editor

In the Borehole Editor you can:

  • Edit the soil profiles for any of the boreholes in the model.
  • Specify drainage conditions.

Editing Boreholes

The soil profiles for any of the boreholes can be modified in the Borehole Editor, although there are a few points to note:

  • Any change of Material type is applied to all boreholes.
  • When you use the Insert Layer Above and Insert Layer Below buttons, the default layer thickness for all boreholes is 0 m.
  • When you use the Delete Layer option, that layer is deleted from all boreholes.
  • The Drained Ground Surface checkbox applies to the entire surface.
  • For each soil layer, a Drained at Bottom checkbox can be selected. The drainage settings are global. If you set the bottom of a layer to be drained, it is drained in all boreholes.

Layer Drainage

If the Time-dependent Consolidation Analysis option is selected in Project Settings, then you will be able to define the drainage conditions at the bottom of each layer in the Edit Borehole dialog. This allows you to define drainage at the interface between soil layers, as described below.

Drained at Bottom

For each soil layer, a Drained at Bottom checkbox can be selected in the Soil Layers dialog.

If this checkbox is selected, then the layer is assumed to be freely drained at the bottom (i.e. excess pore pressure will be automatically set to zero at the interface between layers).

If this checkbox is NOT selected, then the interface will NOT be a drainage path (i.e. excess pore pressure can exist at the interface).

Below shows some examples of recommended settings with options:

Case 1: Sand underlain by clay

  • For the case with Sand layer and clayer layer underneath, clay type still have some excess pore pressure build up at the interface, so it's advised to leave the 'drained at the bottom' option off as set by the default.
  • The scenario where it is feasbile to use this option is when the layer underneath has drainage path which makes the excess pore pressure close to zero.

Case 2: Thick clay layer, H > 5 ft

  • Many engineers will try to avoid defining thick clay layers in Settle3 as the tiny consolidation results from it is not reasonable. The reasoning behind this in real life is that you'll hardly see pure clay soils. There will always be some percentage of sand mixed with clay.
  • Within the clay layers, there will be some drainage and thereby the consolidation will take place. The best way to model this thick clay layer is to have a thin (~0.1 ft) drainage layer every 5 feet increment. Drainage is allowed from the upper clay soils through the drainage soils. With or without defining this drainage layers, where will be significant consolidation settlement value changes.
  • Using driainage at bottom option will allow excess pwp to reach zero between interface, creating drainage layer with high permeability assigned to it will allow driainage path between layers but will not cause complete drainage path. you can also add wick drains to add additional drainage condition within soil layers.

Drained Ground Surface

By default, it is assumed that the ground surface is freely draining (i.e. excess pore pressure cannot exist at the ground surface). Consequently, the Drained Ground Surface checkbox (in the lower left corner of the Soil Layers dialog) is always turned on by default.

If for some reason you wish to define the ground surface as NOT freely drained, then you can turn OFF the Drained Ground Surface checkbox. If you do this, then excess pore pressure can exist at the ground surface (i.e. as if an impermeable membrane covered the ground surface).

NOTE: additional drainage conditions can be specified by defining wick drains, see the Add Wick Drain Region topic for details.

Account Icon - click here to log in or out of your account Shopping Cart icon Click here to search our site Click here to close Learning Tech Support Documentation Info Chevron Delete Back to Top View More" PDF File Calendar Location Language Fees Video Click here to visit Rocscience's LinkedIn page Click here to visit Rocscience's YouTube page Click here to visit Rocscience's Twitter page Click here to visit Rocscience's Facebook page Click here to visit Rocscience's Instagram page Bookmark Network Scroll down for more Checkmark Download Print Back to top Single User Multiple Users CPillar Dips EX3 RocFall RocPlane RocSupport RocTopple RS2 RS3 RSData RSPile Settle3 Slide2 Slide3 SWedge UnWedge Commercial License Education License Trial License Shop safe & secure Money-back guarantee