Expert Modelling: Hands-on help from Rocscience Engineers. Register Here
 

Search Results

Define Joint Properties

To define liner interface properties:

  1. Select the Support Support workflow tab workflow tab.
  2. Select Define Liners Properties Define Liners Properties icon from the toolbar or select: Support > Liners > Define Interface Properties / Materials > Joints > Define Joint Properties from the drop down menu.
  3. TIP: you can also right-click on the viewing window and select Define Joint Properties from the menu.

  4. You will see the Define Liner Interfaces Properties dialog with a list of currently defined liner interface property types at the left of the dialog.Define Linear Interfaces Properties dialog
  5. To create a new liner property type select the Add Add button button, or choose an existing liner from the list at the left of the dialog.
  6. Under Slip Criterion section, choose a failure criterion and enter the required input parameters. There are four different liner interface types to choose from:
  7. Repeat steps 4 and 5 as required to define different liner property types.
  8. See the above links for details about each liner interface type and the required input parameters description.

Slip Criterion

Slip Criterion = None

If the slip criterion is selected as none, then joints will behave elastically, according to the normal and shear joint stiffness. Plastic slip cannot occur.

The Mohr-Coulomb, Barton-Bandis, Geosynthetic Hyperbolic and Material Dependent models are described below. If Slip Criterion is set to one of these models then local joint slip can occur if the shear stress on a joint element exceeds the shear strength as defined by the Slip Criterion parameters.

Slip Criterion = Mohr-Coulomb

The Mohr-Coulomb Slip Criterion parameters are:

  • Cohesion
  • Friction Angle
  • Tensile Strength

Residual Strength

If you select the Residual Strength checkbox for the Mohr-Coulomb criterion, you can define residual values of tensile strength, cohesion and friction angle. The residual strength parameters will be in effect if joint slip or tensile failure occurs (i.e. peak strength envelope has been exceeded).

Check Mohr-Coulomb failure criterion for more details on the perimeters.

Slip Criterion = Barton-Bandis

The Barton-Bandis Slip Criterion parameters are:

  • JCS
  • JRC
  • Residual Friction Angle

The original Barton equation for the shear strength of a rock joint is given by Eqn.1:

The original Bartin equation for the shear strength of a rock joint Eqn.1

where Basic friction angle variable is the basic friction angle of the failure surface, JRC is the joint roughness coefficient, and JCS is the joint wall compressive strength [Barton, 1973, 1976]. On the basis of direct shear test results for 130 samples of variably weathered rock joints, this was later revised to Eqn.2:

Equation 2 Eqn.2

where Residual friction angle variable is the residual friction angle of the failure surface [Barton and Choubey, 1977]. Barton and Choubey suggest that Residual friction angle variable can be estimated from Eqn.3:

Equation used to estimate residual friction angle Eqn.3

where r is the Schmidt hammer rebound number on wet and weathered fracture surfaces and R is the Schmidt rebound number on dry unweathered sawn surfaces. Equations 2 and 3 have become part of the Barton-Bandis criterion for rock joint strength and deformability [Barton and Bandis, 1990].

For further information on the shear strength of discontinuities, including a discussion of the Barton-Bandis failure criterion parameters, see Practical Rock Engineering (Chapter 4: Shear Strength of Discontinuities) on the Rocscience website.

Residual Strength

If you select the Residual Strength checkbox for the Barton-Bandis criterion, the residual strength will be given by:

Residual strength equation Eqn.4

(i.e. if joint slip occurs, the JRC and JCS component of the joint shear strength will be set to zero and the shear strength will depend only on the residual friction angle and the normal stress).

Slip Criterion = Geosynthetic Hyperbolic

The Geosynthetic Hyperbolic slip criterion can be used for modeling the shear strength of the interface between a geosynthetic (e.g. geotextile or geogrid) and soil.

The Geosynthetic Hyperbolic slip criterion is defined by the following equation:

Geosynthetic Hyperbolic slip criterion equation Eqn. 5

This equation was derived from a study of the constitutive behaviour of geosynthetic interfaces [ Esterhuizen, Filz & Duncan (2001) ], and has been found to characterize the shear strength of soil / geo-synthetic interfaces, and other types of interfaces. Note the definition of the adhesion and friction angle parameters:

  • Adhesion Adhesion variable is defined as the shear strength at Value that defines shear strength (i.e. the Adhesion for a Hyperbolic shear strength envelope is actually the limiting, maximum shear strength, for high normal stress).
  • Friction angle Friction angle variable is defined as the friction angle at Value where the friction angle is defined .

The following figure illustrates a hyperbolic shear strength envelope.

Hyperbolic shear strength envelope

Hyperbolic Shear Strength envelope

In addition to the peak values of Adhesion and Friction Angle, you may also define residual values of Adhesion and Friction Angle. The residual values will be used in the analysis if the peak strength has been reached. If you do not wish to consider residual strength, then enter zero for these parameters.

NOTE: in order to use the Geosynthetic Hyperbolic slip criterion for modeling geosynthetics, you must use the Structural Interface option to define the geosynthetics. This will automatically create a joint on either side of the geosynthetic. See the Structural Interface Overview for more information.

Slip Criterion = Material Dependent

If the Joint Slip Criterion = Material Dependent, then the joint strength (and optional stiffness) will be derived from the soil or rock materials through which the joint passes. The Material Dependent option is applicable if the soil or rock materials use the Mohr-Coulomb or Hoek-Brown strength options. It is not applicable for the Cam Clay strength options.

The material dependent joint strength is defined in terms of an Interface Coefficient which is used as a multiplier for the cohesion and friction angle of the surrounding material. The Interface Coefficient ( Ci) is applied as follows to determine the joint cohesion and friction angle from the material cohesion and friction angle:

Cjoint = Ci * Csoil

Phi = ArcTan (tan(Phisoil)* Ci)

Residual joint strength parameters are similarly determined from the residual soil/rock strength parameters, if the surrounding material has failed. For Hoek-Brown materials, equivalent values of cohesion and friction angle are first determined, and then the interface coefficient is applied to determine joint strength.

NOTE: material dependent joint stiffness can also be defined as described below.

Normal & Shear Joint Stiffness

Each joint element has a normal and a shear spring stiffness which relate the normal and shear stress on the element to the normal and shear displacement.

Joint stiffness is usually not a well known parameter. Methods of estimating joint stiffness have been derived, see the Estimating Joint Stiffness topic for two possible methods (one method is based on the properties of the joint infilling material, the other is based on the deformation properties of the rock mass and the intact rock).

Material Dependent Joint Stiffness

If the Joint Slip Criterion = Material Dependent (see above for description) then the joint stiffness (and strength) can be defined with respect to the surrounding material properties, using a multiplying coefficient. The Material Dependent joint stiffness coefficient is optional, and can be defined by selecting the Material Dependent Stiffness option and entering a Stiffness Coefficient (Cs).

RS2 uses a zero thickness joint element thus in order to maintain numerical stability and realistic behaviour, the stiffness coefficient is applied as follows to determine the normal and shear joint stiffness based on the material modulus:

Ks = Cs * Young's Modulus soil;

Kn = 10 * Ks

These values were found adequate for most applications; however, material dependent joint stiffness is optional, and the user can input the stiffness values manually if required.

Initial Joint Deformation

Initial Joint Deformation refers to how the joint behaves in regard to the far field stresses.

  • If the Initial Joint Deformation is ON, then the joint will deform based on both the far field stresses and the induced stresses due to any excavations. As a result, the stress field in the vicinity of the joint will be altered from the initial far field distribution. This will be evident if you run an analysis with a joint only (i.e. no excavations).
  • If Initial Joint Deformation is OFF, then a single joint, with no excavation, has no effect at all (try running this). With no Initial Joint Deformation, only the induced stresses from the presence of an excavation or an external load, can cause joint deformation.

Additional Pressure Inside Joint

The Additional Pressure Inside Joint option allows you to apply a pressure within the joint, which will act normal to the joint boundary. The following options are available.

Groundwater Pore Pressure

If you select this check box, then any water pressure within the joint due to groundwater will be accounted for in the joint analysis. This option is applicable if you are using Groundwater analysis available in RS3.

Additional Pressure

If you select this check box, then you can define a (constant) value of pressure which will be applied within the joint. This additional pressure can be used to simulate the pressure due to hydraulic fracturing for example.

Apply Pressure to Liner Side Only

By default, when you apply the Additional Pressure Inside Joint option, the resulting pressure (load) is applied to BOTH sides of the joint. However, there are circumstances when the additional pressure should only be applied to ONE side of the joint.

This option is applicable under the following circumstances:

    1. The joint must be a component of either a lining composition, or structural interface.
    2. The material adjacent to the joint/liner must be soil or other porous material with groundwater pore pressure in effect (i.e. effective stress).
    3. You are applying Additional Pressure Inside the Joint using one of the above options (Groundwater Pore Pressure or Additional Pressure).

Under these circumstances, if you select this check box, then the load represented by the groundwater pore pressure in the joint, will ONLY be applied to the side of the joint which is adjacent to the liner. The side of the joint adjacent to the solid elements will NOT have the additional pressure load applied, since the groundwater pore pressure is already accounted for in the solid elements. If your model fits these criteria, then you should use this option.

The option is NOT applicable and should NOT be used under the following circumstances:

    1. The material adjacent to the joint/liner is hard rock (no pore pressure considered within the solid elements). In this case, the pressure inside the joint should be applied to BOTH sides of the joint (i.e. liner AND solid elements).
    2. Joints which are NOT a component of a Composite Liner or Structural Interface (e.g. a joint boundary).

Apply SSR

The Apply SSR option for joints is ONLY available if you are carrying out a Shear Strength Reduction (SSR) analysis

Furthermore, the Apply SSR checkbox will only be enabled if the joint Slip Criterion = Mohr-Coulomb. (It cannot be applied for Barton-Bandis or Geosynthetic Hyperbolic slip criteria).

The Apply SSR option for joints has the following purpose:

  • By default, if you are carrying out an SSR analysis with RS3, the strength reduction is ONLY applied to the material strength parameters (i.e. rock or soil types which have plastic material strength properties).
  • The strength reduction is NOT applied to joint strength properties (i.e. joints will retain their original strength properties during the SSR analysis).
  • If you want the SSR analysis to be applied to joints, then select the Apply SSR checkbox for the desired joint type(s). The SSR analysis will then be applied to material AND joint properties. By default, the Apply SSR option for joints is always OFF.
Account Icon - click here to log in or out of your account Shopping Cart icon Click here to search our site Click here to close Learning Tech Support Documentation Info Chevron Delete Back to Top View More" PDF File Calendar Location Language Fees Video Click here to visit Rocscience's LinkedIn page Click here to visit Rocscience's YouTube page Click here to visit Rocscience's Twitter page Click here to visit Rocscience's Facebook page Click here to visit Rocscience's Instagram page Bookmark Network Scroll down for more Checkmark Download Print Back to top Single User Multiple Users CPillar Dips EX3 RocFall RocPlane RocSupport RocTopple RS2 RS3 RSData RSPile Settle3 Slide2 Slide3 SWedge UnWedge Commercial License Education License Trial License Shop safe & secure Money-back guarantee