Expert Modelling: Hands-on help from Rocscience Engineers. Register Here
 

Search Results

Stress Analysis

The following options are available on the Stress Analysis page of the Project Settings dialog. These options can be used to customize the parameters that control the finite element stress analysis in RS3.

Maximum Number of Iterations

The Maximum Number of Iterations controls the maximum number of iterations allowed in each Load Step. The default value is 500.

Tolerance

The Tolerance value defines the point at which the finite element solution is considered to have converged. The Tolerance for the stress analysis is a dimensionless parameter that represents the allowable unbalanced energy in the system, and corresponds to the Convergence Criterion (Absolute Energy, Absolute Force, or Absolute Force & Energy). For a given Load Step:

  • If the energy imbalance of a current state (iteration) is less than the Tolerance value, then the solution is considered to have converged and the iterations are stopped.
  • If the Tolerance value is not achieved within the specified Maximum Number of Iterations (i.e. the energy imbalance remains greater than the Tolerance value), then the solution process is deemed not to have converged for the specified convergence parameters.

For more information about Tolerance and convergence, see the Convergence Criteria document in the RS3 theory section.

The default Tolerance is 0.001. The suggested range of values is 0.01 to 0.001. If your model is experiencing convergence problems, you can try increasing the Tolerance value in order to achieve convergence. However, you must be aware that there can be many reasons why a model is not converging (often related to incorrect modeling procedures or input parameters), and increasing the Tolerance will not necessarily give you a correct answer if your model is incorrect. Larger Tolerance values (e.g. 0.01) will speed up the solution time, but may give a less accurate solution. Smaller values (e.g. 0.0001) may give a more accurate solution, however, this will vary depending on the problem, and will increase computation time.

NOTE: for an elastic analysis (i.e. all materials are elastic), the Tolerance is not used since the solution is "exact". The Tolerance is only used for plasticity analysis (i.e. at least one material is defined as having plastic material properties).

Number of Load Steps

By default,the Number of Load Steps used by Compute at each stage is automatically determined by RS3 (Number of Load Steps = Auto). To force Compute to use a pre-determined Number of Load Steps, enter a number from 1 to 1000 in the Number of Load Steps option of Project Settings. You can also use the Adaptive option.

AUTO OR FIXED

When Number of Load Steps = Auto, the number of Load Steps used at each stage will not necessarily be the same. When a Fixed Number of Load Steps is entered, this number will be used at each stage of the calculation. In general, it is recommended that the user leave Number of Load Steps = Auto. Entering a user-defined (fixed) Number of Load Steps is recommended for advanced users only.

ADAPTIVE

When using the Adaptive load steps option, the program will predict the value of the next load step based on the number of iterations that were required for the previous steps to converge. To customize the Adaptive load steps option select the Advanced button button.

  • Minimum Number of Iterations - Minimum number of iterations needed to converge. If the number of iterations used to converge is smaller than the minimum than the minimum number of iterations, then the next load step will be scaled up to the scale up value.
  • Initial Load Increment - The initial load increment used at the beginning of each stage.
  • Minimum Load Increment - Minimum value of the load increment.
  • Number of Iterations to Track Convergence - Number of pairs of iteration and tolerance that the program will use to predict if the current load step will converge.
  • Scale up force increment if convergence is less than minimum number of iterations - If the number of iterations used to converge is smaller than the minimum number of iterations, then the next load step will be scaled up to the scale up value.
  • Scale down force increment if no convergence - If the simulation is not converged with the current value of the load increment, the program will recalculate with a scaled down load increment.

CONVERGENCE TYPE

You may choose Absolute Energy, Absolute Force, or Absolute Force & Energy as the convergence criterion used for the finite element stress analysis.

ACCELERATE INITIAL STIFFNESS

The Accelerate Initial Stiffness option can be used to accelerate matrix computations and reduce computation time, by scaling the iterative displacements using an acceleration parameter, alpha, for every other iteration. The maximum and minimum values for the acceleration parameter, alpha, can be specified.

TENSILE FAILURE REDUCES HOEK-BROWN TENSILE STRENGTH TO ZERO

If this checkbox is selected and you are using the Hoek-Brown or Generalized Hoek-Brown failure criterion, then the tensile failure of a solid element will automatically reduce the tensile strength to zero.

TENSILE FAILURE REDUCES SHEAR STRENGTH TO RESIDUAL

There are two possible failure modes of a solid element in RS3: tensile or shear. Either or both of these modes may occur in a given element.

If the Tensile failure reduces shear strength to residual checkbox is selected in Project Settings, then if tensile failure occurs at a point in a material (and shear failure has not already occurred), the shear strength of the material at that point will be automatically reduced to the residual shear strength parameters for that material. This is a realistic assumption to make, particularly for brittle materials.

It is important to note that this option is only applicable for materials where the material type = Plastic, and the residual strength parameters are less than the peak strength parameters.

This option will have no effect for materials with the following parameters:

  • material type = Elastic, or
  • material type = Plastic, but the residual strength parameters are equal to the peak strength parameters (i.e. perfectly plastic material properties).

If the checkbox is not selected, then the shear strength parameters will not be reduced if tensile failure occurs in a material (i.e. the tensile and shear failure modes will be independent of each other).

ABORT CALCULATION WHEN NON-CONVERGENCE IS DETECTED

If this checkbox is selected, then the calculation will be aborted when non-convergence is detected. Non-convergence is defined as reaching the maximum number of iterations without achieving the desired tolerance for the overall model. This option avoids further computation to save time for the user, so that they can review the model parameters.

Account Icon - click here to log in or out of your account Shopping Cart icon Click here to search our site Click here to close Learning Tech Support Documentation Info Chevron Delete Back to Top View More" PDF File Calendar Location Language Fees Video Click here to visit Rocscience's LinkedIn page Click here to visit Rocscience's YouTube page Click here to visit Rocscience's Twitter page Click here to visit Rocscience's Facebook page Click here to visit Rocscience's Instagram page Bookmark Network Scroll down for more Checkmark Download Print Back to top Single User Multiple Users CPillar Dips EX3 RocFall RocPlane RocSupport RocTopple RS2 RS3 RSData RSPile Settle3 Slide2 Slide3 SWedge UnWedge Commercial License Education License Trial License Shop safe & secure Money-back guarantee