Rocscience International Conference 2025 is going to take place in Sydney, Australia Read more

Search Results

Grouted Dowel

The Grouted Dowel bolt type can be used to model support which has a variable bonded (grouted) length.

grouted dowel with bonded length and faceplate
Grouted Dowel with Bonded Length and Faceplate

General

Force Application and Orientation

  • Force Application: Active or Passive
  • Use Bolt Orientation Efficiency (optional): Cosine Tension/Shear or Linear Tension/Shear
    • The tensile capacity determined from the Bolt Force Diagram assumes that a bolt is mobilized in pure tension. However, this will usually not be the case, and a bolt which intersects a block may also be in shear or even compression. A Bolt Orientation Efficiency factor (0 to 1) can be applied to the tensile capacity of the bolt determined from the Bolt Force Diagram. The efficiency factor accounts for the fact a bolt will in general not be mobilized in pure tension but may include shear or compression. See the Bolt Orientation Efficiency topic for more information.

Tensile

  • Tensile Capacity represents the maximum tensile capacity of the bolt itself (i.e., steel tensile capacity), independent of the plate capacity or the bond capacity. Units are Force.

Shear and Compression

  • Use Shear Capacity (optional): Shear Capacity
    • A bolt may support a block by virtue of the shear strength of the bolt, acting against the sliding direction of the block.
  • Use Compression Capacity (optional): Compression Capacity
See the implications of Use Bolt Orientation Efficiency, Use Shear Capacity, and Use Compression Capacity in the Bolt Implementation topic.

Pullout and Stripping

Plate Capacity

  • Plate Capacity represents the maximum load which can be sustained by the plate assembly which connects the dowel to the exposed block face. Units are Force.

Bond Strength

  • Bond Strength expressed as a Force per unit Length, where the length refers to the length along the dowel. The maximum pullout force is therefore simply the Bond Length of the dowel, multiplied by the Bond Strength.
  • Material Dependent (optional): sum of bond strength of material x bolt length passing through material specified, otherwise the global Bond Strength is used
  • Use Percent of Length can be either
    • Length of actual bond length, starting from the end of the bolt
    • Percent of total bolt length, starting from the end of the bolt

Bolt Force Diagram

The Grouted Dowel tensile properties which are entered in the Define Bolt Properties dialog, are used to determine a Force Diagram for the dowel, as described below.

Consider a dowel which intersects a block as follows:

dowel intersection
Dowel Intersecting Block


Where:

Lw = wedge length = bonded length of dowel within wedge

La = anchorage length = bonded length of dowel embedded in rock beyond wedge

Dowel Parameters:

T = Tensile Capacity (force)

P = Plate Capacity (force)

B = Bond Strength (force / unit length of bond)

For a Grouted Dowel, at any point along the length of the dowel, there are 3 possible failure modes which are considered:

  • Pullout (force required to pull the anchorage length La of the bolt out of the rock)
  • Tensile Failure (maximum axial capacity of the bolt)
  • Stripping (wedge failure occurs, and bolt remains embedded in rock)

The maximum force which can be mobilized by each failure mode, at any point along the bolt length, is given by the following equations:

Pullout: F1 = B * La (Eqn.1)

Tensile: F2 = T (Eqn.2)

Stripping: F3 = P + B * Lw (Eqn.3)

In order for stripping to occur, the Plate Capacity must be exceeded. The Plate Capacity is included in the stripping force equation and added to the bond capacity along the block length Lw.

At any point along the length of the bolt, the force which is applied to the block by the bolt is given by the MINIMUM of these three forces.

Applied Force = min (F1, F2, F3)
(Eqn.4)

A Force diagram for a Grouted Dowel, which exhibits all three failure modes, is shown below. In this case, the Plate Capacity is less than the Tensile Capacity, and therefore "stripping" is a possible failure mode. If the Plate Capacity is greater than the Tensile Capacity, then stripping cannot occur, and the Force diagram will be determined only by the Tensile and Pullout failure modes.

Tensile Bolt Force Diagram
Tensile Bolt Force Diagram
Rocscience logo, click here to return to the homepage Portal Account Portal Account Log In Log Out Home Shopping Cart icon Click here to search our site Click here to close Learning Tech Support Documentation Info Chevron Delete Back to Top View More" Previous Next PDF File Calendar Location Language Fees Video Click here to visit Rocscience's LinkedIn page Click here to visit Rocscience's YouTube page Click here to visit Rocscience's X page Click here to visit Rocscience's Facebook page Click here to visit Rocscience's Instagram page Click here to visit Rocscience's Reddit page Bookmark Network Scroll down for more Checkmark Download Print Back to top Single User Multiple Users RSLog RocFall3 CPillar Dips EX3 RocFall RocPlane RocSlope3 RocSupport RocTopple RS2 RS3 RSData RSPile Settle3 Slide2 Slide3 SWedge UnWedge RocTunnel3 RocSlope2 BlastMetrix ShapeMetriX Fragmenter Commercial License Education License Trial License Shop safe & secure Money-back guarantee