Define Hydraulic Properties (Seepage Analysis)

The options available in the Define Hydraulic Properties dialog correspond to the Groundwater Method specified in the Project Settings dialog. If the Groundwater Method = Finite Element Analysis, then you will be able to define the permeability characteristics for your materials.

Material permeability is required by the finite element analysis in order to solve the seepage problem (i.e. determine the flow and pore pressure distribution throughout the model). The available options are described below.

Saturated Permeability

A saturated permeability, Ks, must always be specified for a material. However, note:

If you are using a User Defined Permeability Function (see below for details), then the saturated permeability is specified as the first point of the permeability function (i.e. permeability at matric suction = 0). In this case, the saturated permeability option, Ks, will be disabled.
For all other permeability function models (i.e. Simple, van Genuchten etc), the saturated permeability Ks is enabled.

Anisotropic Permeability Parameters

Anisotropic permeability may be specified for a material (i.e. permeability varies with direction), by specifying a Factor and Angle, which defines the relative permeability in two orthogonal directions.

K2 / K1 is the factor which specifies the relative permeability in the direction orthogonal to the K1 direction. NOTE that the K1 permeability is the "primary" permeability defined by the Saturated Permeability Ks, and the unsaturated permeability model you have defined in the dialog.
K1 Angle is the angle which specifies the direction of the K1 permeability. The K1 Angle is specified relative to the positive X (horizontal) direction, as indicated by the picture in the dialog.

EXAMPLE: if K2 / K1 = 0.5 and K1 Angle = 0, then the permeability in the HORIZONTAL direction = Ks (in the saturated zone), and the permeability in the VERTICAL direction = 0.5 * Ks (in the saturated zone).

Permeability Models

The following models are available in Phase2, for describing the permeability in the unsaturated zone, as a function of matric suction. NOTE:

Plot button

After entering the parameters for the selected model, you can select the Plot button to view the actual permeability function which is defined by the model and the parameters you have entered.

Pick button

If you select the Pick button in the dialog, you will see another dialog, from which you can select from a list of materials, with representative parameters for the selected model. (References for the data are provided in the dialog). If you select OK in this dialog, the currently selected parameters will be automatically loaded into the Define Hydraulic Properties dialog.

Simple

With the Simple model, an unsaturated permeability function is automatically determined by Phase2, based on the magnitude of the saturated permeability Ks. To view the function determined by Phase2, you can select the Plot button in the dialog. If you do this, you will see that the unsaturated permeability, for the Simple model, simply decreases by an order of magnitude, within the initial range of matric suction values. The permeability then remains constant for higher values of suction.

Brooks and Corey

The following equations define the Brooks-Corey permeability function (Brooks and Corey, 1964):

For :

Eqn.1a

For :

Eqn.1b

where: = Pore size index

= bubbling pressure

= matric suction

K = permeability

Ks = saturated permeability

Fredlund and Xing

The following equation defines the Fredlund-Xing permeability function (Fredlund and Xing, 1994):

Eqn.2

where: A, B and C are the model parameters

= 2.7182818 …

= matric suction

K = permeability

Ks = saturated permeability

Gardner

The following equation defines the Gardner permeability function (Gardner, 1956):

Eqn.3

where: a and n are the model parameters

h = pressure head (suction)

K = permeability

Ks = saturated permeability

Van Genuchten

The following equations define the van Genuchten permeability function (van Genuchten, 1980):

Eqn.4a

Eqn.4b

where: = degree of saturation

h = pressure head (suction)

are the model parameters

K = permeability

Ks = saturated permeability

NOTE: the parameters m and n are related as follows:

Eqn. 4c

However, the user can specify a value of m which is independent from n, by selecting the Custom m checkbox, and entering a value for m.

User Defined

For complete flexibility in defining permeability functions, a User Defined Permeability Function can be defined, as follows:

Select the New button in the Define Hydraulic Properties dialog.
You will see the User Defined Permeability Function dialog.
Enter a Name for the function.
Enter the Matric Suction and Permeability values, which define the required function. As you enter the data, the graph at the right of the dialog, will display the function you are defining.

NOTE: the data points on the graph can be moved graphically by clicking on them with the mouse and dragging.

When all data has been entered, select OK, and you will be returned to the Define Hydraulic Properties dialog.
In the Define Hydraulic Properties dialog, the Name of the User Defined Permeability Function you have defined, will now appear in the Model drop-down list. It can now be selected at any time, just like any of the other permeability models.

The following options allow you to edit, delete, copy, import or export User Defined Permeability Functions.

Edit

To modify an existing User Defined Permeability Function, select the Name of the function from the Model list, and then select the Edit button. You can then edit the data which defines the function, in the User Defined Permeability Function dialog.

Delete

To delete an existing User Defined Permeability Function, select the Name of the function from the Model list, and then select the Delete button.

Copy

To create a copy of an existing User Defined Permeability Function, select the Name of the function from the Model list, and then select the Copy button. Enter a new name in the dialog which appears, and select OK. A new function will automatically be created, and the Name will appear in the Model list.

Import / Export

User Defined Permeability Functions in Phase2 can be saved in their own separate file, if desired.

To save a User Defined Permeability Function file, select the Export button in the User Defined Permeability Function dialog. These files have a .FN5 filename extension.
To import a User Defined Permeability Function file, select the Import button in the User Defined Permeability Function dialog.